Diagnostic manual includes detailed service and repair and information, maintenance instructions, troubleshoot information, wiring details, specifications for Perkins Engine 4016-E61TRS. This diagnostic manual is intended to assist you in the repair and maintenance of Perkins engine.
Diagnostic manual comes in PDF, includes 176 pages. We recommend to use Adobe PDF Reader, to be sure all images / graphics will display correctly.
This manual allows to detect and resolve problems arising and uncertainties.
Models covered:
4016-E61TRS - 16 cylinder, turbocharged, gas engines
Contents:
- 1 Electronic system overview
- System overview
- General introduction
- Engine speed governing
- Ignition control
- Air-fuel ratio control
- Start/Stop sequencing
- Engine monitoring/protection
- Service tools
- Required service tools
- TIPSS connections
- 2 Programming parameters
- Introduction
- Customer passwords
- Engine identification parameters
- Engine serial number
- Equipment ID
- Timing control parameters
- First desired base timing
- Second desired base timing
- Air fuel ratio control parameters
- Fuel quality
- Gas specific gravity
- Desired oxygen at full load
- Oxygen sensor override
- Oxygen feedback enabled status
- Air / Fuel proportional gain
- Air / Fuel integral gain
- Speed control parameters
- Low idle speed
- Engine accel. rate
- Governor type setting
- Engine speed droop
- Governor proportional gain
- Governor integral gain
- Governor derivative gain
- Adjustment of governor gains
- Start/Stop control parameters
- Crank terminate speed
- Engine purge cycle time
- Engine cooldown duration
- Cycle crank time
- Overcrank time
- Engine speed drop time
- Engine pre-lube time out period
- 3 Troubleshooting with ab event code
- Introduction
- Engine overspeed shutdown
- High jacket water temperature alarm
- High jacket water temperature shutdown
- High oil temperature shutdown
- Raw water temperature shutdown
- Raw water temperature alarm
- Low jacket water temperature start inhibit (E38) or low jacket water alarm (E37)
- Low oil pressure (E40, E100)
- Abnormal battery voltage (E42, E43, E50)
- High gas fuel temperature (E223)
- Closed circuit breather fault (E159)
- Low water level fault (E131)
- Low oil level fault (E171)
- Tubine inlet temperature fault (E870-1) (E870-3)
- High gas supply pressure (E267)
- Engine overcrank fault (E225)
- Customer fault stop requested (E269) or engine ESTOP pressed (E264)
- Low gas pressure ing=hibit (E158) or low gas pressure shutdown request (E160)
- Gas energy content setting low (E229) or gas energy content setting high (E230) or fuel quality out of range (E231)
- Detonation alarm
- Exhaust port temperature high
- Exhaust port temperature deviating low
- 4 Troubleshooting with a diagnostic code
- Diagnostic codes
- Active Diagnostic codes
- Logged Diagnostic codes
- Logged Events
- Diagnostic Terminology
- Quick Reference Sheet For ECM Diagnostic Codes
- Quick Reference Sheet For Temperature Sensing Module Diagnostic Codes
- 5 Functional Tests
- Inspecting electrical connectors
- Electrical power supply to the ECM
- Analogue sensor open or short circuit test
- PWM sensor circuit test
- Oxygen sensor buffer supply circuit
- Oxygen sensor signal circuit test
- Speed/Timing sensor
- Detonation sensors
- ECM Start/Stop output circuit test
- Ignition primary circuit shorted or open
- Ignition transformer secondary and spark plugs
- ECM Status indicator output circuit test
- +5V Sensor voltage supply circuit test
- +8V Sensor voltage supply circuit test
- Throttle actuator solenoid circuit test
- Temperature sensing module (TSM) test
- Techjet gas valve
- 6 Calibrations
- Oxygen sensor calibration procedure
- Speed/timing sensor calibration
- Turbine inlet temperature interface module calibration
- 7 Glossary of terms
- 8 Wiring details
- Wiring layout
- 'A' Bank sensor rail layout
- 'A' Bank sensor rail wiring
- 'B' Bank sensor rail layout
- 'B' Bank sensor rail wiring
- ECM Enclosure layout
- ECM Enclosure wiring
- ECM Enclosure wiring 2
- ECM Enclosure terminal strip connections
- Power and starter harness and wiring
- Throttle valve and manifold sensor harness and wiring
- 'A' Bank ignition pipe layout and wiring
- 'B' Bank ignition pipe layout and wiring
- Exhaust thermocouple harness and wiring
- ITSM to ECM Enclosure harness and wiring
- OEM Connection details
- ECM Enclosure connector pinouts
- Communications connector
- OEM Connector
- Ignition connector 'A' bank
- Ignition connector 'B' bank
- Power and starter connector
- Sensor connector 'A' bank
- ITSM Connector
- Sensor connector 'B' bank
- Throttle valve and manifold sensor connector
- CAN Bus connector
- Connection details - J1
- Connection details - J2
Our company provides for sale original spare part catalogs, workshop manuals, diagnostic software for all models of engines, cars, trucks, buses, forklifts, tractors, harvesters, cranes, buldozers, generators, construction and agricultural machines, motorcycles. To purchase a catalog online, please add the product to your cart, fill in the contact form online. Our managers proceed your order the same day.
