Perkins 3008/CV8 Engines 3000 Series Workshop Manual PDF

This workshop manual is intended for serve, repair and troubleshoot Perkins 3008/CV8 Engines 3000 Series.
Workshop manual contains detailed repair and maintenance information, maintenance instructions, descriptions of repair and troubleshoot procedures, general safety inforation, etc.
This workshop manual comes in PDF format. For work with manual you need to install the application Adobe PDF Reader.
Workshop manual will be able to quickly and easily troubleshoot and fix any problems.

Models covered:
3008/CV8 - 8 cylinder diesel engines for industrial applications

Contents:

• 10 General information
  • Introduction
  • Bank and cylinder bore identification
  • Engine identification
  • General safety precautions
  • Safety
  • Useful information
  • Approved lubricants and fluids
• 11 Specifications
  • Basic engine data
  • Engine
  • Cooling system
  • Fuel system
  • Lubrication system
  • Induction and exhaust systems
  • Electrical equipment
  • Auxiliary equipment
  • Recommended applied torques
  • Recommended specific applied torques
  • Recommended nominal applied torques
• 12 Cylinder head assembly
  • General description
  • Pedestal rocker cover
  • Pedestal rocker assembly
  • Rocker boxes
  • Tappet clearances
  • Cylinder head assembly
  • Valves, valve springs and valve rotators
  • Push rods
  • Fits and clearances
• 13 Pistons and connecting rods
  • General description
  • Big end bearings
  • Piston and connecting rod assembly
  • Piston rings
  • Piston and rings
  • Connecting rod
  • Fits and clearances
• 14 Crankshaft assembly
  • General description
  • Crankshaft pulley
  • Front oil seal
  • Rear oil seal assembly
  • Crankshaft assembly
  • Main bearings and thrust washers
  • Fits and clearances
• 15 Timing gears and timing case
  • General description
  • Timing case
  • Auxiliary drive assembly
  • Double idler gear
  • Idler gear for the lubricating oil pump
  • Fits and clearances
• 16 Cylinder block assembly
  • General description
  • Crankcase
  • Cylinder liners
  • Fits and clearances
• 17 Camshafts and engine timing
  • General description
  • Camshafts
  • Engine timing
  • Fits and clearances
• 18 Induction and exhaust system
  • Engines fitted with a single turbocharger
  • General description
  • Air cleaners
  • Induction manifolds - two-piece type
  • Induction manifolds - one-piece type
  • Exhaust manifolds
  • Turbocharger
  • Turbocharger: CV6404
  • Turbocharger: CV17019
  • Engines fitted with twin turbochargers
  • General description
  • Air cleaners and induction manifolds
  • Exhaust manifolds
  • Turbocharger
  • Turbocharger: CV18504
• 19 Lubrication system
  • General description
  • Filter canisters
  • By-pass filter assembly
  • Sump
  • Lubricating oil pump
  • Relief valve - integral with oil cooler
• 20 Fuel system
  • General description
  • Primary fuel filter
  • Fuel filter canister
  • Fuel injectors
  • Fuel lift pump
  • Fuel injection pump and governor
  • Fuel injection pump - Bosch S3000
  • Special tools - Bosch S3000
  • Governor - Bosch RQV
  • Special tools - Bosch RQV Governor
  • Governor - AMBAC
  • Fuel system
• 21 Cooling system
  • General description
  • Radiator
  • Coolant pump
  • Thermostat
  • Fan
  • Fan adaptor
  • Oil cooler - large version
  • Oil cooler - small version
  • Fits and clearances
• 22 Flywheel and flywheel housing
  • General description
  • Flywheel
  • Starter ring
  • Flywheel housing
• 23 Electrical equipment
  • General description
  • Precautions
  • Alternator drive belt
  • Alternator
  • Butec type A13 alternator
  • Butec type A3024 alternator
  • Starter motor
  • Butec MS1A starter motor
  • Electrical switches
  • Engine stop solenoid ('energised-to-run')
• 24 Auxiliary equipment
  • Compressor
• 25 Running-in and test
  • General information
  • Running-in and test
• 26 Special tools
  • List of special tools