New Holland TG Series Tractors, TJ Series Tractors Repair Manual PDF

This Electronic repair manual covers instructions, recommendations, descriptions, troubleshooting information, and also many screenshots, diagrams, and schemes for New Holland TG Series Tractors, TJ Series Tractors. It covers:

SYMPTOM BASED FAULTS - NO FAULT CODES 
Can I utilize my DGPS Universal, DGPS 130, or DGPS EZ-Guide 110 Receiver with
Omnistar HP differential signal?
Low number of satellites when using RTK
RTK GPS users are having problems obtaining or maintaining an RTK Fix due to
inadequate satellite coverage in their location
RDL cannot read CompactFlash Data Card
Losing Configuration Settings When the RDL is Powered Off
Trouble activating Omnistar VBS satellite differential subscriptions on Ag252 GPS Receiver. 
Poor accuracy, non-repeatable pass to pass performance when using RTK 
Poor GPS accuracy or swath performance with the Ag252 receiver. 
Tracking Omnistar HP signal but not receiving an “OK” system status. Message
GPS Status “Wait – D7” (7 represents current number of Satellites). 
Tracking Omnistar HP signal but not receiving an “OK” system status. Message
GPS Status “Wait – D7” (7 represents current number of Satellites). 
WAAS DGPS shifts position after a period of time from startup. 
No GPS position output from the Ag252 receiver after connecting to Ag Remote v2.xx. 
Restore Ag252 Receiver factory settings 
Restore Ag252 Receiver factory settings 
Not tracking RTK corrections, Wait-A7 message (7 represents the number of satellites) 
Not tracking RTK corrections, Wait-A7 message (7 represents the number of satellites) 
Long time to initialize RTK 
Loss of RTK Initialization or RTK Float Status – “Wait-F6” Message
(6 represents the current number of satellites) 
Using WAAS to reduce error when setting up a RTK Base Station location. 
LED sequences for WAAS or Omnistar VBS differential positioning. 
LED sequences for Omnistar HP differential positioning. 
LED sequences for RTK positioning. 
Vehicle Confusion in Swath Orientation 
Steering seems erratic or confused. 
Vehicle continues in Auto Mode, but drifts offline. 
Front wheel drift, hard steering, vehicle fails to come online when in autoguidance, initial installation setup. 
Solid Green LED on the Ag252 receiver, but no GPS Info on the Display – GPS Status None 
Controller Guidance System Fault Code 1 “FE Send Message” 
Controller Guidance System Fault Code 2 “FE Task Init.” 
Controller Guidance System Fault Code 3 “FE Go Trap” 
Controller Guidance System Fault Code 4 “A/D Scan Timeout” 
Controller Guidance System Fault Code 5 “A/D Scan Overrun” 
Controller Guidance System Fault Code 6 “A/D Data Not Ready” 
Controller Guidance System Fault Code 7 “A/D Chan Overrun” 
Controller Guidance System Fault Code 8 “Vpp Jumpered” 
Controller Guidance System Fault Code 9 “Battery Bad” 
Controller Guidance System Fault Code 11 “SP Open Failed” 
Controller Guidance System Fault Code 12 “Matrix Inv. Failed” 
Controller Guidance System Fault Code 13 “MATHERR Exception” 
Controller Guidance System Fault Code 14 “MATHERRF Exception” 
Controller Guidance System Fault Code 15 “Fatal Error Reboot” 
Controller Guidance System Fault Code 16 “App Undefined ISR” 
Controller Guidance System Fault Code 17 “TPU Undefined ISR” 
Controller Guidance System Fault Code 18 “MIOS1 Undefined ISR” 
Controller Guidance System Fault Code 19“QADC Undefined ISR” 
Controller Guidance System Fault Code 21 “Uninit. App Assert” 
Controller guidance System Fault Code 22 “Acc X Overvoltage” 
Controller Guidance System Fault Code 23 “Acc X Undervoltage” 
Controller Guidance System Fault Code 24 “Acc Y Overvoltage” 
Controller Guidance System Fault Code 25 “Acc Y Undervoltage” 
Controller Guidance System Fault Code 26 “Acc Z Overvoltage” 
Controller Guidance System Fault Code 27 “Acc Z Undervoltage” 
Controller Guidance System Fault Code 28 “Gyro X Overvoltage” 
Controller Guidance System Fault Code 29 “Gyro X Undervoltage” 
Controller Guidance System Fault Code 30 “Gyro Y Overvoltage” 
Controller Guidance System Fault Code 31 “Gyro Y Undervoltage” 
Controller Guidance System Fault Code 32 “Gyro Z Overvoltage” 
Controller Guidance System Fault Code 33 “Gyro Z Undervoltage” 
Controller Guidance System Fault Code 34 “Heater Overvoltage” 
Controller Guidance System Fault Code 35 “Heater Undervoltage” 
Controller Guidance System Fault Code 36 “VRef Overvoltage” 
Controller Guidance System Fault Code 37 “VRef Undervoltage” 
Controller Guidance System Fault Code 39 “Steering Overvolt”
Controller Guidance System Fault Code 40 “Steering Overvolt” 
Controller Guidance System Fault Code 40 “Steering Undervolt” 
Controller Guidance System Fault Code 40 “Steering Undervolt” 
Controller Guidance System Fault Code 41 “Man Ovrd Overvolt” 
Controller Guidance System Fault Code 42 “Man Ovrd Undervolt” 
Controller Guidance System Fault Code 43 “Gear Lev Overvolt” 
Controller Guidance System Fault Code 44 “Gear Lev Undervolt”
Controller Guidance System Fault Code 46 “Valve Coil Short” 
Controller Guidance System Fault Code 47 “Valve Coil Imax” 
Controller Guidance System Fault Code 48 “MOSFET Short”
Controller Guidance System Fault Code 49 “Coil Short to GND”
Controller Guidance System Fault Code 50 “Coil Shorted” 
Controller Guidance System Fault Code 54 “SafeMCU Prog. Error” 
Controller Guidance System Fault Code 55 “SafeMCU No Stack” 
Controller Guidance System Fault Code 56 “SafeMCU Msg Timeout” 
Controller Guidance System Fault Code 58 “Angle Out of Bounds” 
Controller Guidance System Fault Code 58 “Steering Unsafe” 
Controller Guidance System Fault Code 59 “MCU2 Vel. Unsafe” 
Controller Guidance System Fault Code 70 “Test Build Expired” 
Controller Guidance System Fault Code 71 “Top FET Sense Err” 
Controller Guidance System Fault Code 76 “VT Assert Failure” 
Controller Guidance System Fault Code 77 “VT Object Pool Buffer Overflow” 
Controller Guidance System Fault Code 78 “VT Comms Error” 
Controller Guidance System Fault Code 79 “VT Watchdog Timeout” 
Controller Guidance System Fault Code 80 “PP Task Assert Failure” 
Controller Guidance System Fault Code 81 “CAN-VT Assert Failure” 
Controller Guidance System Fault Code 81 “CN Task Assert Failure”

Models: IntelliSteer™
Auto Steering System
Troubleshooting TG Series Tractors, 
TJ Series Tractors
Part number 87046843

First of all, to avoid technical failures, breakdowns, and serious injuries, you should familiarize and read yourself with the rules and notes, recommendations, and advice. This guide helps beginners and experienced professionals in the use and maintenance of this equipment.

Features of the Manual
Format: PDF
Language: English
Pages: 95
Compatible with all versions of Windows, Mac, Linux, iPhone, iPad, and Android
The manual includes step-by-step guides and high-quality illustrations to help you perform routine and preventive maintenance effectively.

FAQs
How do I download the manual?
Immediately after payment, we send you the online file by email to your email address within 1-10 minutes of your purchase. So please make sure your email address is correct. Please check your spam/junk folder if you don't see it in your inbox.

Is the manual printable?
it is possible to print the entire instruction or the individual diagrams and schemes.

Still have questions?
Сheck with us if you will have questions or need our help. Our managers will help you.