John Deere Combines Technical Manual TM4387 PDF

For proper operation, quality repair and timely maintenance combines John Deere, you should purchase this technical manual.
Technical manual is a system of care in operation and maintenance, which allows to detect and eliminate problems and inaccuracies.
Manual comes in PDF and includes 1697 pages, which are printable. To view the information you want the program installed Adobe Reader.
This manual contains detailed service information, operating and maintenance instructions, diagrams and charts, service documentation and other additional information that is presented specifically for combines John Deere these models:
932,
942,
952,
955,
965-H,
968-H,
975,
975 Hydro/4,
985,
985 Hydro/4,
1065,
1068-H,
1072,
1075,
1075 Hydro/4,
1085,
1085 Hydro/4.

CONTENTS:

• SECTION 10 - GENERAL
  • Group 00 - Specifications and Special Tools
  • Group 05 - General Information
  • Group 10 - Pre-Delivery Inspection, Delivery Service and After-sales Inspection
  • Group 15 - Lubrication and Periodic Service
  • Group 20 - Engine and Combine Tune-Up and Adjustments
  • Group 25 - Combine Separation
• SECTION 20 - ENGINE REPAIR
  • Group 00 - Specifications and Special Tools
  • Group 05 - Cylinder Head, Valves, Camshaft and Balancer Shafts (Engines 3179, 4239, 6359)*
  • Group 06 - Cylinder Head, Valves, Camshaft and Balancer Shafts (Engine 6466)**
  • Group 10 - Cylinder Block, Liners, Pistons and Connecting Rods (Engines 3179, 4239, 6359)*
  • Group 11 - Cylinder Block, Liners, Pistons and Connecting Rods (Engine 6466)**
  • Group 15 - Crankshaft, Main Bearings and Flywheel (Engines 3179, 4239, 6359)*
  • Group 16 - Crankshaft, Main Bearings and Flywheel (Engine 6466)**
  • Group 20 - Lubrication System (Engines 3179, 4239, 6359)*
  • Group 21 - Lubrication System (Engine 6466)**
  • Group 25 - Cooling System (Engines 3179, 4239, 6359)*
  • Group 27 - Fan Drive Contershaft
  • Group 26 - Cooling System (Engine 6466)**
  • Group 30 - Timing Gear Train (Engines 3179, 4239, 6359)*
• SECTION 30 - FUEL AND AIR REPAIR
  • Group 00 - Specifications and Special Tools
  • Group 05 - Air Intake System
  • Group 10 - Fuel System
  • Group 11 - Fuel Filter with Water Trap and Electrical Fuel Transfer Pump from Serial No. 041201
  • Group 15 - Roto Diesel Fuel Injection Pump
  • Group 20 - Roosa Master Fuel Injection Pump
  • Group 25 - Robert Bosch Fuel Injection Pump
  • Group 30 - Roosa Master Fuel INjection Nozzles
  • Group 35 - Robert Bosch Fuel Injection Nozzles KDEL (21 mm)
  • Group 40 - Speed Control Linkage
• SECTION 40 - ELECTRICAL SYSTEM
  • Group 00 - Specifications and Special Tools
  • Group 05 - Diagnosing Malfunctions
  • Group 10 - Electrical System Components
  • Group 15 - Wiring Diagrams and Wiring Harnesses
  • Group 20 - Starting Motor (Bosch) Starting Motor (John Deere)
  • Group 30 - Alternator (Bosch)
  • Group 35 - Alternator (Delcotron)
  • Group 40 - Electrical Leveling Control System (Sidehill Combines)
• SECTION 41 - MODIFIED ELECTRICAL EQUIPMENT ON COMBINES FROM SERIAL NO. 041201
  • Group 05 - Wiring Harnesses and Connectors
  • Group 06 - Electrical Circuits and Wirong Diagrams
  • Group 07 - Testing Individual Circuits
  • Group 10 - Starting Motor
  • Group 15 - Alternator
  • Group 20 - Components
  • Group 25 - Shaft Low Speed Monitor System
  • Group 30 - Harvestrak Combine Monitor - Functional Description and Tests
  • Group 35 - Harvestrak Combine Monitor - Repair
  • Group 40 - Electromagnetic Transmission Brake
• SECTION 50 - POWER TRAIN
  • Group 00 - Specifications and Special Tools
  • Group 05 - Variable Ground Speed Drive
  • Group 10 - "Posi Torq" Ground Drive
  • Group 15 - Engine Clutch and Clutch Linkage (932, 942, 952)
  • Group 20 - Engine Clutch and Clutch Linkage (955)
  • Group 25 - Engine Clutch (955 to 1085)
  • Group 26 - Clutch fron Ser. No. 044137
  • Group 30 - Reverser Clutch, Control and Linkage
  • Group 35 - Hydrostatic Drive
  • Group 40 - Front Axle (932, 942, 952)
  • Group 45 - Transmission and Differential (955 to 1085 Hydro/4)
  • Group 50 - Final Drives (955, 965, 975 to 1085 Hydro/4)
  • Group 51 - Rice Drives
  • Group 55 - Final Drive (Sidehill Combines)
  • Group 60 - Track System
• SECTION 60 - BRAKES AND REAR AXLE
  • Group 00 - Specifications and Special Tools
  • Group 05 - Parking Brake (932, 942, 952)
  • Group 10 - Parking Brake (955 to 1085 Hydro/4)
  • Group 15 - Footbrakes (Disk Brakes Acting on Transmission)
  • Group 16 - Footbrakes (With Integrated Slave Cylinder)
  • Group 20 - Footbrakes (Disk Brakes Acting on Front Wheels)
  • Group 25 - Rear Axle
  • Group 30 - Rear Axle (Sidehill Combines)
  • Group 35 - V-Support for Wide Rear Axle
• SECTION 70 - HYDRAULIC SYSTEM
  • Group 00 - Specifications and Special Tools
  • Group 05 - General Information, Diagnosing Malfunctions
  • Group 06 - Hydraulic Symbols and System Layout
  • Group 10 - Pressure Tests
  • Group 15 - Hydraulic Oil Reservoir, Filter, Suction and Pressure Lines
  • Group 20 - Hydraulic Pump and Flow Divider
  • Group 25 - Tandem (Dual-Gear) Hydraulic Pump
  • Group 30 - Triple Hydraulic Pump
  • Group 35 - Single and Three Spool Control Valves
  • Group 40 - Seven Spool Control Valve
  • Group 41 - Seven Spool Control Valve (from Serial No. 041201)
  • Group 45 - Hydraulic Cylinders (up to a certain serial no.)
  • Group 50 - Hydraulic Cylinders (from a certain serial no.)
  • Group 55 - Nitrogen Accumulators
  • Group 60 - Hydrostatic Steering
  • Group 65 - Hydraulic Brakes
  • Group 70 - Hydraulic Clutch Control
  • Group 71 - Clutch Operation with Integrated Slave Cylinder
  • Group 75 - Transmission Brake
  • Group 80 - Hydraulic Components (Sidehill Combines)
  • Group 85 - Hydraulic Drive Reel or Belt Pick-Up System
  • Group 90 - Hydraulic Reverser Motor
• SECTION 80 - MISCELLANEOUS
  • Group 00 - Specifications and Special Tools
  • Group 05 - General Information
  • Group 10 - Bearings and Shafts
  • Group 15 - Belts and Chains
• SECTION 90 - OPERATOR'S CAB
  • Group 00 - Specifications and Special Tools
  • Group 05 - Cab Ventilation
  • Group 10 - Air Conditioning System
  • Group 15 - Air Conditioning System Components
  • Group 20 - Heater
• SECTION 95 - OPERATOR'S PLATFORM WITH SG-2 CAB (-044136)
  • Group 00 - Specifcications and Special Tools
  • Group 05 - Cab Ventilation
  • Group 10 - Air Conditioning System
  • Group 15 - Compressor
  • Group 20 - System Components
  • Group 25 - Cab Heating System
  • Group 30 - Operator's Seat
  • Group 35 - SG2 Cab
• SECTION 96 - OPERATOR'S PLATFORM WITH SG-2 CAB (044137-)
  • Group 05 - Cab Ventilation
  • Group 10 - Air Conditioning System
  • Group 15 - System Service
  • Group 20 - System Testing
  • Group 25 - Compressor
  • Group 30 - System Components
  • Group 35 - Cab Heating System
  • Group 40 - Operator's Seat
  • Group 45 - SG2 Cab
• SECTION 100 - CUTTING PLATFORM AND CORN HEAD
  • Group 00 - Specifications and Special Tools
  • Group 05 - General Information, Diagnosing Malfunctions
  • Group 10 - Cutting Platform and Knife Drive
  • Group 11 - 200-Series Platform
  • Group 15 - Variable Reel Speed Drive
  • Group 20 - Corn Head
  • Group 25 - Corn Head Gear Case
• SECTION 110 - FEEDER HOUSE
  • Group 05 - General Information, Diagnosing and Malfunctions
  • Group 10 - Feeder Drive
  • Group 15 - Feeder House (with Integrated Cutting Platform)
  • Group 20 - Feeder House (with Quick-Tach Cutting Platform)
  • Group 21 - Feeder House (with Quick-Tach Cutting Platform)
  • Group 25 - Chain Transmission - Cutting Platform Drive
  • Group 30 - Hydraulic Reverser
• SECTION 120 - SEPARATOR AND CLEANING UNIT
  • Group 00 - Specifications and Special Tools
  • Group 05 - General Information, Diagnosing Malfunctions
  • Group 10 - Separator Drive
  • Group 15 - Threshing Cylinder, Variable Cylinder Drive
  • Group 20 - Cylinder Drive Reduction Gear (Up to Serial No. 039866)
  • Group 21 - Cylinder Drive Reduction Gear (From Serial No. 039867)
  • Group 25 - Concave
  • Group 30 - Beater, Beater Variable Drive
  • Group 35 - Cross Shaker
  • Group 40 - Straw Walkers, Cleaning Shoe with Sieves and Fan
• SECTION 130 - ELEVATORS, GRAIN TANK AND GRAIN TANK UNLOADING AUGERS
  • Group 05 - General Information, Diagnosing Malfunctions
  • Group 10 - Elevator and Auger Drives
  • Group 15 - Clean Grain Auger and Elevator
  • Group 20 - Lower Tailings Auger, Elevator and Upper Auger
  • Group 25 - Grain Tank Leveling Auger and Unloading Auger
  • Group 30 - Outer Unloading Auger and Housing
• SECTION 140 - SPECIAL EQUIPMENT
  • Group 00 - Specifications and Special Tools
  • Group 05 - Straw Chopper with Centrifugal and Electric Clutch
  • Group 10 - Straw Chopper with Direct Drive
  • Group 15 - Straw Spreader