John Deere 1133 1144 1155 1157 1158 Combines TM4476 Technical Manual PDF

Technical manual contains full information regarding repair procedures, guidance on maintenance and adjustment of faults combines John Deere these models:
1133,
1144,
1155,
1157,
1158.
The interface of this manual is verysimple and convenient, it allows you to quickly and easily find the information you need for repair and maintenance.
This manual comes in PDF. For work with manual you need to install the application Adobe PDF Reader.
Electronic technical manual allows to identify existing and potential problems, to carry out maintenance and repair problem areas and troubleshooting.

CONTENTS:

• SECTION 10 - GENERAL
  • Group 05 - Specifications
• SECTION 20 - ENGINE REPAIR
  • Group 05 - Removal and Installation, 4-cyl. Engine
  • Group 10 - Removal and Installation, 6-cyl. Engine
• SECTION 30 - FUEL AND AIR REPAIR
  • Group 05 - Fuel Filter With Water Trap And Electrical Fuel Transfer Pump
• SECTION 40 - ELECTRICAL SYSTEM REPAIR
  • Group 05 - Connectors
  • Group 10 - Electrical System Components
  • Group 15 - Starting Motor
  • Group 20 - Alternator
  • Group 25 - Low Shaft Speed Monitor System
  • Group 30 - Electromagnetic Transmission Brake
• SECTION 50 - POWER TRAIN REPAIR
  • Group 05 - Variable Ground Speed Drive
  • Group 10 - Engine Clutch And Mechanical Clutch Operation (3-Speed Transmission)
  • Group 15 - Engine Clutch Operation (4-Speed Transmission)
  • Group 20 - Engine Clutch Operation (4-Speed Transmission)
  • Group 25 - Three-Speed Transmission
  • Group 30 - Four-Speed Transmission With Differential
  • Group 35 - Final Drives, Differential (3-Speed Transmission)
  • Group 40 - Final Drives (4-Speed Transmission)
  • Group 45 - Final Drive On Rice Combine (4-Speed Transmission)
• SECTION 60 - BRAKES, REAR AXLE AND STEERING REPIAR
  • Group 05 - Parking Brake (3-Speed Trnsmission)
  • Group 10 - Parking Brake (4-Speed Transmission)
  • Group 15 - Brake Operation
  • Group 20 - Foot Brakes (3-Speed Transmission)
  • Group 25 - Foot Brakes (4-Speed Transmission)
  • Group 30 - Foot Brakes With Integrated Slave Cylinder
  • Group 35 - Hydrostatic Steering Unit
  • Group 40 - Rear Axle
  • Group 45 - V-Support For Wide Rear Axle
  • Group 50 - Steering Cylinder
• SECTION 70 - HYDRAULIC SYSTEM REPAIR
  • Group 05 - Hydraulic Oil Reservoir And Lines
  • Group 10 - Hydraulic Pump
  • Group 15 - 4-Spool Control Valve With Flow Divider
  • Group 20 - Hydraulic Cylinders
  • Group 25 - Hydraulic System Diaphragm-Type Accumulator
• SECTION 80 - MISCELLANEOUS
  • Group 05 - Bearings And Shafts
  • Group 10 - Drive Belts
  • Group 15 - Drive Chains
  • Group 20 - Specifications, Special Tools, and Torques
• SECTION 90 - OPERATOR'S PLATFORM WITH CAB
  • Group 05 - Safe Handling Of Refrigerants
  • Group 10 - Air Conditioning Compressor
  • Group 15 - Air Conditioning System Components
  • Group 20 - Air Conditioning System Service And Tests
  • Group 25 - Cab Ventilation System
  • Group 30 - Cab Heating System
  • Group 35 - Operator's Cab
  • Group 40 - Control Levers
  • Group 45 - Operator's Seat
• SECTION 100 - CUTTING PLATFORM AND CORN HEAD
• SECTION 110 - FEEDER HOUSE
  • Group 05 - Feeder House Drive
  • Group 10 - Feeder House With Compact Cutting Platform
  • Group 15 - Feeder House With Quick-Tach Cutting Platform
• SECTION 120 - SEPARATOR AND CLEANING UNIT
  • Group 05 - Stone Trap
  • Group 10 - Separator Drive
  • Group 15 - Variable Cylinder Drive
  • Group 20 - Threshing Cylinder
  • Group 25 - Concave
  • Group 30 - Beater Variable Drive
  • Group 35 - Beater
  • Group 40 - Cross Shaker
  • Group 45 - Straw Walkers
  • Group 50 - Cleaning Shoe, Grain Return Pan And Auger Housing
  • Group 55 - Fan And Variable Speed Drive
• SECTION 130 - GRAIN PROCESSING
  • Group 05 - Clean Grain And Tailings Augers
  • Group 10 - Clean Grain Elevator
  • Group 15 - Tailings Elevator
  • Group 20 - Upper Tailings Auger
  • Group 25 - Grain Tank Leveling Auger
  • Group 30 - Grain Tank Center Fill Auger
  • Group 35 - Inner Grain Tank Unloading Auger
  • Group 40 - Outer Grain Tank Unloading Auger
  • Group 45 - Discharge Tube
• SECTION 140 - SPECIAL EQUIPMENT
  • Group 05 - Straw Chopper Drive
  • Group 10 - Straw Chopper Rotor Bearings
• SECTION 220 - ENGINE OPERATION
• SECTION 230 - FUEL AND AIR INTAKE SYSTEM OPERATION
  • Group 05 - General Information, Fuel Filter And Fuel Transfer Pump
• SECTION 240 - ELECTRICAL SYSTEM - OPERATION AND TESTS
  • Group 05 - General Information
  • Group 10 - Circuit plan, Wiring Diagram And Wiring Harnesses
  • Group 15 - Checking Indicator Lights
  • Group 20 - Checking Low Shaft Speed Monitor System
  • Group 25 - Checking Straw Warning Device
  • Group 30 - Checking Electromagnetic Transmission Brake
• SECTION 250 - POWER TRAIN - OPERATION AND TESTS
  • Group 05 - Engine Clutch And Operation (3-Speed)
  • Group 10 - Engine Clutch And Operation (4-Speed)
  • Group 15 - Three-Speed Transmission
  • Group 20 - Four-Speed Transmission
• SECTION 260 - BRAKES, REAR AXLE AND STEERING - OPERATION AND TESTS
  • Group 05 - Brake Operation
  • Group 06 - Foot Brake And Operation (Combines With Rice Equipment)
  • Group 10 - Operation And Flow Diagram 0 Hydrostatic Steering
  • Group 15 - Diagnosing Steering System Malfunctions
  • Group 20 - Primary (Steering) Circuit Testing
• SECTION 270 - HYDRAULIC SYSTEM - OPERATION AND TESTS
  • Group 05 - Hydraulic Circuit Symbols
  • Group 10 - Hydraulic Lift Circuit
  • Group 15 - Lifting System - Diagnosing Malfunctions
  • Group 20 - Hydraulic Lift Circuit - Testing
• SECTION 290 - OPERATOR'S PLATFORM AND CAB - OPERATION AND TESTS
  • Group 05 - Cab Venilation System
  • Group 10 - Air Cinditioning System
  • Group 15 - Safe Handling Of Refrigerants
  • Group 20 - Testing Air Conditioning System
  • Group 25 - Cab Heating System