Hitachi Crawler Crane CX350/500 Drag Line Service Manual PDF

This Service Manual covers the following PDF guides for Hitachi Crawler Cranes CX350/500 Models (Drag Line):
Technical Manual (Operational Principle)
Technical Manual (Troubleshooting)/Circuit Diagram & Harness
Workshop Manual

Note: If you need some specific manual (from those listed in the set), then you can purchase the listed manuals separately. To do this, you just need to click on the name of the desired manual and you will follow the link to the page where you can purchase it.

These technical manuals come in PDF format. So, it doesn't require any installation (Instant Download). We recommend you to use the application Adobe Acrobat Reader for working with PDF instructions. Also, we recommend you print these manuals and use them as handbooks when they will be necessary.

You are buying a factory service manual for Hitachi Crawler Cranes. After your purchase, within 3-5 minutes we send to your email address the link for download with all necessary recommendations. If you want the same factory information shipped to you on a DVD please pay the Shipping charge during checkout or write to us about it.

Models covered:
CX350,
CX500.

Vol Numbers:
TO224E-00
TT224E-00
W224E-00

CONTENTS (Operational Principle):

• SECTION 1 GENERAL
  • Group 1 Specification
  • Group 2 Component Layout
  • Group 3 Component Specifications
• SECTION 2 SYSTEM
  • Group 1 Hydraulic System
  • Group 2 Electrical System
• SECTION 3 COMPONENT OPERATION
  • Group 1 Pump Device
  • Group 2 Swing Device
  • Group 3 Hoist Device
  • Group 4 Boom Hoist Device
  • Group 5 Control Valve
  • Group 6 Pilot Valve
  • Group 7 Travel Device
  • Group 8 Others (Superstructure)
  • Group 9 Others (Undercarriage)

CONTENTS (Troubleshooting):

• SECTION 4 OPERATIONAL PERFORMANCE TEST
  • Group 1 Introduction
  • Group 2 Standard
  • Group 3 Engine Test
  • Group 4 Crane Test
  • Group 5 Component Test
• SECTION 5 TROUBLESHOOTING
  • Group 1 Diagnosing Procedure
  • Group 2 Component Layout
  • Group 3 Troubleshooting A
  • Group 4 Troubleshooting B
  • Group 5 Electrical System Inspection

CIRCUIT DIAGRAM & HARNESS:
CX350 HYDRAULIC CIRCUIT DIAGRAM
CX350 ELECTRICAL CIRCUIT DIAGRAM (1)
CX350 ELECTRICAL CIRCUIT DIAGRAM (2)
CX500 HYDRAULIC CIRCUIT DIAGRAM
CX500 ELECTRICAL CIRCUIT DIAGRAM (1)
CX500 ELECTRICAL CIRCUIT DIAGRAM (2)

CONTENTS (Workshop Manual):

• SECTION 1 GENERAL INFORMATION
  • Group 1 Precautions for Disassembling and Assembling
  • Group 2 Tightening
• SECTION 2 SUPERSTRUCTURE
  • Group 1 Cab
  • Group 2 Counterweight
  • Group 3 Main Frame
  • Group 4 Pump Device
  • Group 5 Control Valve
  • Group 6 Swing Device
  • Group 7 Hoist Device
  • Group 8 Boom Hoist Device
  • Group 9 Pilot Valve
  • Group 10 Pilot Shut-Off Valve
  • Group 11 Solenoid Valve
  • Group 12 Shuttle Valve
  • Group 13 Booster Valve
• SECTION 3 UNDERCARRIAGE
  • Group 1 Swing Bearing
  • Group 2 Travel Device
  • Group 3 Center Joint
  • Group 4 Track Adjuster
  • Group 5 Front Idler
  • Group 6 Upper and Lower Roller
  • Group 7 Track
  • Group 8 Side Frame Extend/Retract Cylinder
• SECTION 4 ENGINE AND ACCESSORY
  • General Introduction
  • Engine
  • Electrical Equipment
  • Turbocharger
  • Fuel Injection Pump
  • Injection Pump Governor
  • Generator
  • Starter
  • Air Compressor
  • Calibration