Case STX375 STX425 STX450 and STX500 PDF Operator’s manuals

These PDF manuals contain important information on the safe operation, setup, and maintenance of your tractor's Case the Steiger STX Series.

Use this manual as a guide to keeping your tractor running reliably. Refer to the detailed contents below to find necessary information and items specific to your tractor.

Instructions in PDF format. It is very convenient and simple to work in this format. It is enough to install an application that supports this format - Adobe Acrobat Reader or any other analog. After the purchase, within 3-5 minutes we will send a download link with all the necessary recommendations to your email address.

Models:
STX375
STX425
STX450
STX500

Contents:

• 1.TO THE OWNER
  • STX SERIES STEIGER TRACTORS
  • PRODUCT IDENTIFICATION AND SERIAL NUMBERS
  • CHEMICAL TANK MOUNTING
  • BUSINESS BAND RADIOS
  • PRE-CONDITIONING NEW TRACKS
• 2.SAFETY/DECALS
  • SAFETY
  • SAFETY DECALS
  • ROLL OVER PROTECTIVE STRUCTURE (ROPS)
  • SEAT BELTS
  • TRACTOR WARNING LAMPS AND SMV SYMBOL
  • IMPLEMENT WARNING LAMPS AND SMV SYMBOL
  • SAFETY CHAIN
• 3.OPERATING CONTROLS
  • TRACTOR ACCESS
  • OPERATORS SEAT WITH AIR SUSPENSION
  • STEERING COLUMN CONTROLS
  • STEERING COLUMN ADJUSTMENT
  • FOOT PEDALS
  • CENTER CONSOLE CONTROLS
  • RH ARMREST CONTROL CONSOLE
  • REMOTE VALVE FUNCTION CONTROL
  • ARM REST CONTROL CONSOLE ADJUSTMENT (IF EQUIPPED)
  • UPPER CONSOLE CONTROLS
  • STANDARD HVAC CONTROL SYSTEM
  • AUTOMATIC CLIMATE CONTROL OPERATION (IF EQUIPPED)
  • AUTOMATIC CLIMATE CONTROL OPERATION
  • DEFOG CONTROL OPERATION
  • TROUBLESHOOTING THE HVAC CONTROL SYSTEM
• 4.INSTRUMENTATION
  • ROPS POST INSTRUMENT CLUSTER
  • PROGRAMMING THE DISPLAY MONITOR
  • INSTRUMENT PANEL BACKLIGHT INTENSITY
  • CHANGING THE REMOTE VALVE EXTEND/RETRACT VALUES (IF EQUIPPED)
  • CHANGING TIRE RADIUS
  • RADAR SENSOR CALIBRATION
  • RADAR CALIBRATION PROCEDURE
  • TIRE AVERAGE ROLLING RADIUS CHART
  • DYNAMIC ROLLING RADIUS
  • CRITICAL WARNING DISPLAYS
  • NON-CRITICAL WARNING DISPLAYS
  • DIAGNOSTIC WARNING DISPLAYS
  • INFORMATION WARNING DISPLAYS
• 5.OPERATING INSTRUCTIONS
  • BEFORE STARTING THE ENGINE
  • RUN-IN PROCEDURE
  • ENGINE OVERSPEED
  • SEAT BELT
  • NORMAL ENGINE STARTING PROCEDURE
  • STOPPING THE ENGINE
  • COLD TEMPERATURE OPERATION
  • TOWING THE TRACTOR
  • TRANSPORTING THE TRACTOR
  • POWERSHIFT TRANSMISSION OPERATION
  • (IF EQUIPPED)
  • 24-SPEED TRANSMISSION OPERATION (IF EQUIPPED)
  • DIFFERENTIAL LOCK
  • (IF EQUIPPED)
  • CONSTANT ENGINE SPEED OPERATION (IF EQUIPPED)
• 6.FIELD OPERATION
  • OPERATING THE POWER TAKEOFF (PTO)
  • STANDARD DRAWBAR
  • THREE POINT HITCH PREPARATION
  • HITCH COUPLER - CATEGORY III OR IV-N
  • HITCH OPERATION
  • REMOTE HYDRAULICS
  • AUXILIARY IMPLEMENT POWER CONNECTIONS
• 7.IN FIELD PERFORMANCE
  • TRACTOR BALLAST
  • FRONT AND REAR SUITCASE WEIGHTS
  • FRONT SUITCASE WEIGHT, TIE BOLT AND CLAMP INSTALLATION
  • WHEEL WEIGHTS
  • WHEEL WEIGHT BOLT TORQUE
  • TIRE AND RIM SERVICE
  • TIRE PRESSURE FOR MAXIMUM TIRE LOAD AT RATED INFLATION
  • WHEEL BOLT TORQUES
  • WHEEL OFFSET DIRECTION CHANGE
  • WHEEL TREAD SETTING - DUALS
  • TRIPLE WHEEL TREAD SETTING
  • SCRAPER OPERATING PROCEDURES
• 8.LUBRICATION/FILTERS/FLUIDS/MAINTENANCE
  • LUBRICATION AND MAINTENANCE
  • PLASTIC AND RESIN PARTS
  • LUBRICANTS AND CAPACITIES
  • ENGINE LUBRICATION
  • GRILLE AND HOOD ACCESS
  • LUBRICATION AND MAINTENANCE CHART
  • AIR INDUCTION SYSTEM
  • PRESSURE COOLING SYSTEM
  • SCA SERVICE REQUIREMENTS
  • INSPECTION OF TRACKS AND UNDERCARRIAGE
  • TRACK ROTATION
  • TRACK (BELT) TENSION RELEASE
  • TRACK (BELT) ALIGNMENT
• 9.ELECTRICAL SYSTEM
  • ELECTRICAL SPECIFICATIONS
  • GENERAL SERVICE INFORMATION
  • GENERAL SPECIFICATIONS
• 10.GENERAL SPECIFICATIONS
  • TRACTOR WEIGHTS
  • APPROXIMATE TRAVEL SPEEDS (MPH)
  • APPROXIMATE TRAVEL SPEEDS (MPH)
  • DETAIL INDEX