Bomag Single Drum Roller BW 219 D-4/PD-4 Service Manual PDF

A service manual provides information on repair, and maintenance, instructions, diagrams, special tools, etc, one word all information witch you need for comfort use and maintenance of the Bomag equipment. Also, the service manual includes a complete description of repair and troubleshoot procedures, illustrations, and diagrams for single drum roller Bomag following models:

BW 219 D-4/PD-4
S/N 101 582 72 > S/N 101 582 73 >

This manual addresses the professionally qualified personnel and helps in the correct and efficient repair and maintenance work Bomag roller equipment. This manual describes the disassembly/assembly, installation, and repair of components and assemblies.

This manual - this is index file in PDF format, on English, so with help, this format you can to find, copy, print individual chapters, and pages. - all you need. Also, the Bomag manual is designed to work on a personal computer, laptop, or smartphone, only we recommend to install the applicationAdobe PDF Reader for comfort and correct view all diagrams and information.

You can preview this manual due to the detailed table of contents and if you decide to purchase this manual, click on the buy now, and within a few minutes, you will receive an email with a link to the product and all the recommendations.

TABLE of CONTENTS:

• General
  • 1.1 Introduction
  • 1.2 Safety regulations
  • 1.3 General repair instructions
  • 1.4 Tightening Torques
• Maintenance
  • 2.1 General notes on maintenance
  • 2.2 Fuels and lubricants
  • 2.3 Table of fuels and lubricants
  • 2.4 Running-in instructions
  • 2.5 Maintenance chart
• Technical data
  • 3.1 Technical data
• Connection overview
  • 4.1 Connection overview
• Tests and adjustments
  • 5.1 Special tools, tests, and adjustments
  • 5.2 Checking the rotation speeds
  • 5.3 Checking / adjusting the neutral positions of the travel pump
  • 5.4 Pressure tests in the travel circuit
  • 5.5 Checking / adjusting the vibrator shaft speeds
  • 5.6 Pressure measurements in the vibration circuit
  • 5.7 Check the leakage rate of the vibration motor
  • 5.8 Pressure test in steering circuit
• Flushing and bleeding
  • 6.1 Special tools for flushing
  • 6.2 Flushing - general
  • 6.3 Flushing schematic travel circuit (distribution travel pump)
  • 6.4 Flushing the travel circuit (travel pump distribution)
  • 6.5 Flushing schematic travel circuit (distribution axle motor)
  • 6.6 Flushing the travel circuit (axle motor distribution)
  • 6.7 Flushing schematic for vibration drive
  • 6.8 Flushing the vibration circuit
  • 6.9 Bleeding the travel circuit
  • 6.10 Bleeding the vibration circuit
• Fundamental electrics
  • 7.1 Understanding circuit diagrams
  • 7.2 Terminal designations
  • 7.3 Current and voltage
  • 7.4 Resistance
  • 7.5 Series / parallel connection
  • 7.6 Ohm's law
  • 7.7 Electrical energy
  • 7.8 Formula diagram
  • 7.9 Metrology
  • 7.10 Diodes, relays, fuses
  • 7.11 Batteries
  • 7.12 Three-phase generator
  • 7.13 Electric starter
  • 7.14 Telemecanique switch
  • 7.15 Inductive proximity switches
  • 7.16 Angle sensor with current output
  • 7.17 Plug connectors
  • 7.18 Deutsch plug, series DT and DTM
  • 7.19 Plugs and terminals in spring clamping technology
• Special tools, electrics
  • 8.1 Special tools, electrics
• Machine-related electrics
  • 9.1 Electrics BEM (BOMAG Evil-meter)
  • 9.2 Seat contact module
• Speedometer Module
  • 10.1 Speedometer module
• Service Training
  • 11.1 Service Training Machine
• Air conditioning system
  • 12.1 Physical basics
  • 12.2 Refrigerant R134a
  • 12.3 Compressor oil/refrigeration oil
  • 12.4 Working principle of the air conditioning system
  • 12.5 Monitoring devices
  • 12.6 Description of components
  • 12.7 Checking the compressor oil level
  • 12.8 Checking the magnetic clutch
  • 12.9 Inspection and maintenance work
  • 12.10 Checking, replacing the refrigerant compressor V-belt
  • 12.11 Service the air conditioning
  • 12.12 Drying and evacuation
  • 12.13 Emptying in case of repair
  • 12.14 Leak test
  • 12.15 Filling instructions
  • 12.16 Trouble shooting in the refrigerant circuit, basic principles
  • 12.17 Trouble shooting, refrigerant circuit diagram
  • 12.18 Trouble shooting procedure
  • 12.19 Steam table for R134a
  • 12.20 Heating control/air conditioning control
• Replacing the cab window panes
  • 13.1 Assembly of window panes
  • 13.2 Special tools
  • 13.3 Auxiliary materials
  • 13.4 Removing and installing the window pane
• Drum
  • 14.1 Special tools, drum, single drum rollers
  • 14.2 Repair overview for drum
  • 14.3 Removing and installing the drum
  • 14.4 Repairing the drum
  • 14.5 Dismantling, assembling the change-over weights
  • 14.6 Changing the rubber buffers and adjusting the pretension
• Oscillating articulated joint
  • 15.1 Special tools
  • 15.2 Repair overview oscillating articulated joint
  • 15.3 Removing and installing the oscillating articulated joint
  • 15.4 Dismantling the oscillating articulated joint
  • 15.5 Assembling the oscillating articulated joint
• Suppliers documentation
  • 16.1 Travel pump/vibration pump series 90R
  • 16.2 Travel drive series 51
  • 16.3 Transmission CR
  • 16.4 Axle DANA 193
• Circuit diagrams
  • 17.1 Wiring diagram
  • 17.2 Wiring diagram
  • 17.3 Hydraulic diagram