This service manual provides instructions for proper routine servicing and adjustment of the Bobcat, and detailed overhaul instructions of the power train, loader hydraulic/hydrostatic system and general mainframe components.
Using this service manual you can serve, troubleshoot and solve any problems that arise.
This manual is a file PDF, which contains 320 pages, any one of which we can be printed easily. We recommend to use Adobe PDF Reader, to be sure all images / graphics will display correctly.
Models covered:
974,
975.
CONTENTS:
- FOREWORD
- MAINTENANCE SAFETY
- PREVENTIVE MAINTENANCE
- AIR INLET SYSTEM, ENGINE
- BOB-TACH
- CLUTCH, ADJUSTMENT
- CONTROL LEVER LOCK
- COOLING SYSTEM, ENGINE
- CRANKCASE VENT TUBE
- ELECTRICAL SYSTEM MAINTENANCE
- ENGINE MAINTENANCE (GENERAL)
- FAN BELT, ADJUSTMENT
- FILTER SCREEN, TO CLEAN 100 MESH
- FINAL DRIVE CHAIN
- FLUSHING THE COOLING SYSTEM
- FUEL SPECIFICATIONS
- FUEL SYSTEM CHARGING
- FUEL SYSTEM (GENERAL)
- FUEL SYSTEM SERVICE, 974
- FUEL SYSTEM SERVICE, 975
- FUEL TANK, REMOVAL OF
- HYDRAULIC FLUID
- HYDRAULIC FLUID, TO CHECK, ADD OR REPLACE
- HYDRAULIC/HYDROSTATIC SYSTEM (GENERAL)
- HYDRAULIC RESERVOIR
- HYDRAULIC RESERVOIR - REMOVAL OF WATER OR HYDRAULIC FLUID
- HYDRAULIC SYSTEM LEAKS, TO CHECK FOR
- HYDRAULIC TRANSMISSION
- INTRODUCTION
- LUBRICATION
- OIL AND FILTER REPLACEMENT, ENGINE
- OIL COOLER
- REAR GRILL AND ENGINE COVER
- ROPS AND SKID PLATE AREA, CLEANING
- SERVICE INTERVALS
- SIDE PANEL (FENDER) REMOVAL OF
- TILTING THE ROPS (OPERATOR ENCLOSURE)
- TIRE MAINTENANCE
- TIRE REPLACEMENT
- TIRE ROTATION
- TIRES
- TO TRANSPORT
- WHEEL NUTS
- HYDRAULIC SYSTEM
- BASIC OPERATING PRINCIPLE OF THE HYDRAULIC SYSTEM
- CONTROL VALVE, REMOVAL OF
- CONTROL VALVE SERVICE
- HYDRAULIC CONTROLS
- HYDRAULIC CYLINDER, INSPECTION OF
- HYDRAULIC FILTER SERVICE
- HYDRAULIC LIFT & TILT CYLINDER, TO CHECK
- HYDRAULIC PUMP
- HYDRAULIC TESTING
- LIFT CYLINDER
- TILT CYLINDER SERVICE
- TROUBLESHOOTING
- HYDROSTATIC SYSTEM
- CHARGE PUMP, HYDROSTATIC
- CHECK VALVE, REMOVAL OF
- CONTROL ASSEMBLY, REMOVAL OF
- DIRECTIONAL CONTROL, ADJUSTMENT TO
- DISPLACEMENT CONTROL VALVE (PUMP & MOTOR)
- FLUID AND FILTER
- HYDRAULIC FLUID COOLER
- HYDROSTATIC CIRCUITRY
- HYDROSTATIC MOTOR, REMOVAL OF
- HYDROSTATIC OPERATING PRINCIPLE
- HYDROSTATIC PUMP, REMOVAL OF
- PUMP AND MOTOR CONTROL, ADJUSTMENT OF
- TRANSMISSION STARTING PROCEDURE
- TROUBLESHOOTING HYDROSTATIC SYSTEM
- MECHANICAL TRANSMISSION
- AXLES
- CLUTCH SERVICE
- FINAL DRIVE CHAIN, ADJUSTMENT OF
- FINAL DRIVE, INSTALLATION OF
- FINAL DRIVE IDLER
- GENERAL INFORMATION
- REDUCTION GEARCASE DESCRIPTION
- TRANSFER CHAINCASE SERVICE
- MAIN FRAME
- LIFT ARM BUSHING, REPLACEMENT OF
- LIFT ARM PIVOT PIN, REPLACEMENT OF
- LIFT ARMS
- ROPS
- ROPS, REMOVAL AND INSTALLATION OF
- ROPS TILT CONTROL SERVICE
- ELECTRICAL SYSTEM
- BATTERY, INSTALLATION OF
- ELECTRICAL CIRCUITRY
- GENERATOR SERVICE
- GENERATOR OUTPUT, TO CHECK
- PROBLEM ANALYSIS CHART
- STARTER SERVICE
- WIRING, TO CHECK
- WIRING HARNESS
- ENGINE SERVICE (974 PERKINS)
- BALANCER UNIT
- BALANCER UNIT (CENTER MOUNTED)
- CAMSHAFT AND TAPPETS
- COOLING SYSTEM
- CRANKCASE VENTILATION
- CRANKSHAFT AND MAIN BEARINGS
- CRANKSHAFT FRONT SEAL
- CRANKSHAFT REAR OIL SEAL
- CRANKSHAFT
- CYLINDER HEAD
- CYLINDER LINERS
- ENGINE DESCRIPTION
- ENGINE NUMBER
- ENGINE
- ENGINE REPAIR, INTRODUCTION
- EXHAUST SMOKE, DIAGNOSIS CHART
- FLYWHEEL HOUSING
- FLYWHEEL
- FUEL INJECTORS
- FUEL SYSTEM
- LUBRICATING OIL PUN
- LUBRICATING SYSTEM
- PISTON AND CONNECTING RODS
- TIMING CASE COVER
- TIMING FUEL INJECTION PUMP
- TROUBLESHOOTING
- UNIFIED THREADS
- VALVE TIMING, TO CHECK
- ENGINE SERVICE (975 JOHN DEERE)
- BALANCER SHAFTS
- CAMSHAFT
- COOLING SYSTEM
- CRANKSHAFT, MAIN BEARINGS AND FLYWHEEL
- CYLINDER BLOCK, LINERS, PICTONS AND RODS
- CYLINDER HEAD AND VALVES
- CYLINDER HEAD
- CYLINDER HEAD, VALVES, CAMSHAFT AND TIMING GEAR TRAIN
- DETAILED TUNE-UP PROCEDURE
- ENGINE TUNE-UP
- ENGINE REMOVAL
- FUEL SYSTEM
- GENERAL INFORMATION
- LUBRICATION SYSTEM
- PRELIMINARY ENGINE TESTING
- SPECIAL TOOLS
- TUNE-UP PROCEDURES
- TIMING GEAR TRAIN
- VALVE CLEARANCE ADJUSTMENT
- VALVE TRAIN
- TECHNICAL DATA
- ENGINE BREAK-IN INSTRUCTIONS
- LOADER SPECIFICATIONS
- LOADER SPECIFICATIONS (975)
- LOADER TORQUE SPECIFICATIONS
- STANDARD TORQUE SPECIFICATIONS
- TECHNICAL DATA (JOHN DEERE ENGINE)
- TECHNICAL DATA (PERKINS ENGINE)
- U.S. TO METRIC CONVERSIONS
- LOADER SPECIFICATIONS (974 PERKINS)
- LOADER SPECIFICATIONS (975 JOHN DEERE)
- ALPHABETICAL INDEX
Our company provides for sale original spare part catalogs, workshop manuals, diagnostic software for all models of engines, cars, trucks, buses, forklifts, tractors, harvesters, cranes, buldozers, generators, construction and agricultural machines, motorcycles. To purchase a catalog online, please add the product to your cart, fill in the contact form online. Our managers proceed your order the same day.
