New Holland Skid Steer Loader L465, LX465, LX485 Repair Manual PDF

This manual is a dealer repair manual that will need anyone with skid steer loaders New Holland L465, LX465, LX485 and that are themselves willing to improve the maintenance and repair of skid steer loaders.

The repair manual contains guidance on repair and maintenance, service and troubleshoots information, description of service procedures, specific installation instructions, and other service information.

Attention! This New Holland manual contains the section "wiring diagram" in the table of contents, but unfortunately for technical reasons, the manufacturer left this section without information, and pages 3-10 - 3-14 do not contain diagrams. Pay attention to this when shopping. If you have any difficulties or any questions, check them with our support service before ordering.

This electronic manual is in PDF format in English and includes 808 pages, which are printable. To work with this manual, we recommend you install the application Adobe PDF Reader. With this application, you will be sure all images/graphics will display correctly.

This manual covers the following models:

L465
LX465
LX485

CONTENTS:

• SECTION 1 - GENERAL INFORMATION
  • INTRODUCTION
  • ABOUT IMPROVEMENTS
  • SAFETY INFORMATION
  • MACHINE MODEL AND SERIAL NUMBER LOCATION
  • ENGINE MODEL AND SERIAL NUMBER LOCATION
  • HARDWARE TORQUE SPECIFICATIONS CHART
  • HYDRAULIC TUBE AND FITTING INSTALLATION
  • HYDRAULIC TUBE AND FITTING TORQUE SPECIFICATIONS
  • PROPERLY SUPPORT A RAISED MACHINE
  • PROPERLY SUPPORT BOOM ON BOOM LOCK PINS
  • MAJOR UNIT OVERHAUL
  • CAB AND BOOM TILT PROCEDURE
  • CRANING THE SKID-STEER LOADER
  • DRILLING HOLES IN OVERHEAD DASH
  • ADAPTING ATTACHMENTS REQUIRING 12V ELECTRICAL
  • POWER
  • HYDRAULIC SYSTEM COMPATIBILITY
  • ACCESSORY RELAY AND ENGINE FUSE BLOCK
  • SPECIFICATIONS
  • INDEX
• SECTION 2 - ENGINE
  • GENERAL ENGINE INFORMATION
  • ENGINE MODEL AND SERIAL NUMBER LOCATION
  • SAFETY PRECAUTIONS
  • GENERAL ENGINE DATA
  • TROUBLESHOOTING
  • SPECIFICATIONS
  • TORQUE SPECIFICATIONS
  • ENGINE REMOVAL
  • ENGINE DISMANTLING SEQUENCE
  • DISASSEMBLY, INSPECTION, FITS, AND CLEARANCES OF COMPONENT ASSEMBLIES
  • ENGINE REASSEMBLY
  • REINSTALLATION OF ENGINE INTO LOADER FRAME
  • COOLING SYSTEM
  • FUEL SYSTEM
  • ENGINE ELECTRICAL SYSTEMS - ALTERNATOR, STARTER, AND MISCELLANEOUS
  • SPECIAL TOOLS
  • LABOR GUIDE
  • INDEX
• SECTION 3 - ELECTRICAL SYSTEM
  • GENERAL ELECTRICAL INFORMATION
  • SPECIFICATIONS
  • WIRING DIAGRAM
  • ADVANCED WARNING SYSTEM EARLY MODEL - SILVER FRAME
  • ADVANCED WARNING SYSTEM LATER MODEL - GOLD FRAME
  • ELECTRICAL CIRCUITS
  • REMOVAL, INSTALLATION, AND WIRING OF ELECTRICAL COMPONENTS
  • FUEL SYSTEM COMPONENTS
  • WIRE HARNESS
  • ALTERNATOR
  • STARTER
  • MISCELLANEOUS ENGINE COMPONENTS
  • LABOR GUIDE
  • INDEX
• SECTION 4 - FINAL DRIVE, AXLES, BRAKES
  • GENERAL INFORMATION
  • SPECIFICATIONS
  • TROUBLESHOOTING
  • TESTING
  • AXLES
  • FINAL DRIVE
  • PARKING BRAKE
  • LABOR GUIDE
  • INDEX
• SECTION 5 - HYDROSTATIC SYSTEM AND STEERING SYSTEM
  • GENERAL INFORMATION
  • SPECIFICATIONS
  • TROUBLESHOOTING
  • HYDROSTATIC DRIVE SYSTEM TESTING
  • HYDROSTATIC PUMP OVERHAUL
  • HYDROSTATIC MOTOR OVERHAUL
  • HYDRAULIC SYSTEM CLEANING PROCEDURE
  • START-UP PROCEDURE AFTER REBUILD
  • CHARGE CHECK VALVE
  • STEERING SYSTEM
  • LABOR GUIDE
  • INDEX
• SECTION 6 - HYDRAULIC SYSTEM
  • GENERAL INFORMATION
  • SPECIFICATIONS
  • TROUBLESHOOTING
  • HYDRAULIC SYSTEM TESTING.
  • CONTROL VALVE
  • HYDRAULIC PUMP
  • CYLINDERS, BOOM, AND BUCKET
  • HYDRAULIC COOLING, FILTER, RESERVOIR SYSTEM
  • LABOR GUIDE
  • INDEX
• SECTION 7 - SEAT, CAB, ROPS, BOOM LOCK, BOOM, ATTACHMENT MOUNTING PLATE
  • GENERAL INFORMATION
  • SEAT
  • CAB AND ROPS
  • BOOM LOCK PIN/LINKAGE
  • BOOM, UPPER, AND LOWER LINK
  • ATTACHMENT MOUNTING PLATE
  • LABOR GUIDE
  • INDEX